Platformen

This AI Edge Computing Development Kit is based on the Jetson Orin Nano Module providing rich peripheral interfaces such as M.2, DP, USB, etc. This kit also comes with a pre-installed AW-CB375NF wireless network card that supports Bluetooth 5.0 and dual-band WIFI, with two additional PCB antennas, for providing high-speed and reliable wireless network connection and Bluetooth communication. Specifications AI performance 40 TOPS GPU 1024-core N-VIDIA Ampere architecture GPU with 32 Tensor Cores GPU frequency 625 MHz (max) CPU 6-core Arm Cortex-A78AE v8.2 64-bit CPU, 1.5 MB L2 + 4 MB L3 CPU frequency 1.5 GHz (max) RAM 8 GB 128-bit LPDDR5, 68 GB/s Storage 128 GB NVMe Solid State Drive Power 7~15 W PCIE M.2 Key M slot with x4 PCIe Gen3 M.2 Key M slot with x2 PCIe Gen3 M.2 Key E slot USB USB Type-A: 4x USB 3.2 Gen2 USB Type-C (UFP) CSI camera 2x MIPI CSI-2 camera connector Video encode 1080p30 supported by 1-2 CPU cores Video decode 1x 4K60 (H.265) 2x 4K30 (H.265) 5x 1080p60 (H.265) 11x 1080p30 (H.265) Display 1x DisplayPort 1.2 (+MST) connector Interfaces 40-Pin Expansion Header (UART, SPI, I²S, I²C, GPIO), 12-pin button header, 4-pin fan header, DC power jack Networking 1x GbE connector Dimensions 103 x 90.5 x 34 mm Included Waveshare Orin Nano development kit 1x Jetson Orin Nano Module (8 GB) 1x JETSON-ORIN-IO-BASE 1x Cooling Fan 1x 128 GB NVMe Solid State Drive (assembled) 1x Wireless network card (assembled) 1x USB Type A to Type-C cable (1 m) 1x Ethernet cable (1.5 m) 1x Jumper 1x Power adapter (EU) Documentation Wiki

Lees meer minder

The iCEBreaker FPGA board is an open-source educational FPGA development board. The iCEBreaker is great for classes and workshops teaching the use of the open source FPGA design flow through Yosys, nextpnr, IceStorm, Icarus Verilog, Amaranth HDL and others. This means the board is low cost and has a nice set of features to allow for the design of interesting classes and workshop exercises. At the same time it allows the user to use the proprietary vendor tools if they choose to. After the workshop the boards can be easily used as a development board as most GPIO are exposed, broken out and configurable through jumpers on the back of the board. There is only a minimal amount of buttons and LED that can't be disconnected and used for your own purposes. Documentation Workshop

Lees meer minder

If you’re looking for a simple way to start soldering or just want to make your own Dasduino, this soldering set is a great opportunity. "Make your own Dasduino CORE" is an educational set for learning the skill of soldering, with which you end up with a functional microcontroller board. As with the other SMD versions of the Dasduino CORE boards we offer, the possibilities are endless. It is based on the ATmega328P microcontroller, and all SMD components are already soldered on the board. The set also includes a THT socket for the microcontroller, which simplifies the replacement of the microcontroller should it ever become necessary. Included 1x PCB 7x Capacitors (100nF) 4x Capacitors (2.2uF) 2x Capacitors (22pF) 5x Resistors (2.2 kOhm) 5x Resistors (10 kOhm) 3x Resistors (1 kOhm) 1x Resistor (100 kOhm) 1x Resistor (100 ohm) 1x JST battery connector 1x LED (purple) 1x LED (white) 1x LED (blue) 1x LED (red) 1x LED (orange) 1x Socket for ATmega328P 1x ATmega328P microcontroller

Lees meer minder

If you are looking for an easy way to get started with soldering or simply want to make a small portable gadget, this set is a great opportunity. "LED cube" is an educational set for learning the soldering skill, with which you get a small electronic game at the end. After you turn on and shake this board, certain leds will light up randomly and symbolize the number, as if a real die had been thrown. It is based on the Attiny404 microcontroller, programmed in Arduino, and there is a battery on the back which makes this gadget portable. There is also a keychain so you can always carry your new game with you! Soldering is easy according to the markings on the board. Included 1x PCB 1x ATtiny404 microcontroller 7x LEDs 7x Resistors (330 ohm) 1x Resistor (10 kohm) 1x Battery holder 1x CR2032 battery 1x Switch 1x Vibration sensor SW-18020P 1x Keychain ring

Lees meer minder

If you are looking for a simple way to learn soldering, or just want to make a small gadget that you can carry, this set is a great opportunity. Reaction game is an educational kit which teaches you how to solder, and in the end, you get to have your own small game. The goal of the game is to press the button next to the LED as soon as it turns on. With every correct answer, the game gets a bit harder – the time you have to press the button shortens. How many correct answers can you get? It’s based on ATtiny404 microcontroller, programmed in Arduino. At its back, you’ll find CR2032 battery which makes the kit portable. There’s keychain holder as well. Soldering process is easy enough based on the mark on the PCB. Included 1x PCB 1x ATtiny404 microcontroller 4x LEDs 4x Pushbuttons 1x Switch 4x Resistors (330 ohm) 1x CR2032 battery holder 1x Battery CR2032 1x Keychain holder

Lees meer minder

If you are looking for a simple way to learn soldering, or just want to make a small gadget that you can carry, this set is a great opportunity. Stop me game is an educational kit which teaches you how to solder, and in the end, you get to have your own small game. The LEDs go up and down, and your goal is to press the button as soon as the green LED turns on. With every correct answer, the game gets a bit harder – the time you have to press the button shortens. How many correct answers can you get? It’s based on ATtiny404 microcontroller, programmed in Arduino. At its back, you’ll find CR2032 battery which makes the kit portable. There’s keychain holder as well. Soldering process is easy enough based on the mark on the PCB. Included 1x PCB 1x ATtiny404 microcontroller 7x LEDs 1x Pushbutton 1x Switch 7x Resistors (330 ohm) 1x CR2032 battery holder 1x Battery CR2032 1x Keychain holder

Lees meer minder

FLUX Beamo is a powerful and compact 30 W CO2 desktop laser cutter that can cut and engrave a range of materials including metals. With its easy-to-use design, intuitive controls and features, you can effortlessly create amazing things. Built-in HD camera Cutting and engraving is hassle-free with our preview mode. Place your material, preview the work area in the Beam Studio software and engrave. Your design comes out exactly as shown in the preview. Integrated safety features If left opened, auto pause ensures the laser stops. The internal water cooling system provides a stable cutting process. Plus, you can stop production with a single switch at any time. Powerful high resolution laser The Beamo ultra thin laser can engrave exceptional detail down to 0.05 mm wide with a clear resolution of 1,000 dpi. Fitting for any craft or small business project. The most precise compact CO2 laser engraver Beamo's sleek, modern and compact design fits beautifully in any home, school or workshop space. It comes pre-assembled with a metal body and acrylic lid, measuring 615 x 445 x 177 mm. Bring your designs to life with its 30 W CO2 laser operating on a 30 x 21 cm work area. Safe for home and school Beamo prioritises safety with its thoughtful design features. The machine is fully enclosed, and it automatically pauses if the lid is opened during a task. Additionally, there is a single switch for immediate machine shutdown in case of emergencies. Beamo is equipped with a Class 1 laser, which is completely safe under normal use. Specifications Dimensions 615 x 445 x 177 mm Weight 22 kg Work Area 300 x 210 x 45 mm (11.81 x 8,27 x 1.77") Camera Preview Area 300 x 195 mm Voltage AC 110 V / 220 V Touch Panel 1024 x 600 LCD Camera HD CMOS I/O Wi-Fi / Ethernet Laser Spec 30 W CO? Laser Laser Moving Speed 0~300 mm/s Laser Cutting Thickness 0-5 mm (varies by material) Software Mode Vector / Graphic (monochrome, gray scale) Operating System Windows / macOS / Linux Software File Type JPG / PNG / SVG / DXF Included FLUX Beamo (distilled water included) Vent hose Duct Clamp Double sided tape to align the mirror's Ethernet cable Vent Hose Double head wrench Wood piece Torx screwdriver and 2.5 mm hexagonal wrench Funnel 1x Laser Cutter Lubricant Power cord Wifi Dongle USB Beamo Manual Honey Comb Platform (30 W) Downloads Firmware

Lees meer minder

FLUX Ador is the world's first color printing laser cutter. Powered by three high-quality, interchangeable modules, Ador enables you to engrave and cut though a wide range of materials while enhancing your projects with a pop of color. New creative potential with Ador Whether you’re an educator, small business, crafter or designer, with Ador, the application boundary is for you to define. Easy to use Place material then autofocus Drag and drop your design Engrave, cut or print Project Completed! Big workspace, big ideas Ador offers a big working space of 430 x 300 mm, with a depth of 30 mm, expanding the horizons of your creativity. Specifications Dimensions 637 x 488 x 226 mm Weight 19 kg Work Area X&Y: 20 W Diode laser: 430 x 300 mm (X & Y varies with different modules)Z: 30 mm (for all modules) & 20 mm (with prism) Camera Preview Area Whole work area Voltage AC 110-240 V Touch Panel Yes, 8 inches (diagonal) Camera 8 MP I/O USB / WiFi Laser Spec W Diode laser Module Laser Moving Speed 0~400 mm/s Laser Cutting Thickness Varies for different materials Software Mode Vector / Graphic (monochrome, gray scale) Operating System Windows / macOS / Linux Software File Type JPG / PNG / SVG / DXF Included FLUX Ador 20 W diode laser module 6x prism lift Power adapter Power cord Hex key Vent Hose Vent hose Duct Clamp Wooden test piece Laser Cutter Lubricant Downloads Firmware

Lees meer minder

BeagleV-Fire is a revolutionary single-board computer (SBC) powered by the Microchip’s PolarFire MPFS025T 5x core RISC-V System on Chip (SoC) with FPGA fabric. BeagleV-Fire opens up new horizons for developers, tinkerers, and the open-source community to explore the vast potential of RISC-V architecture and FPGA technology. It has the same P8 & P9 cape header pins as BeagleBone Black allowing you to stack your favorite BeagleBone cape on top to expand it’s capability. Built around the powerful and energy-efficient RISC-V instruction set architecture (ISA) along with its versatile FPGA fabric, BeagleV-Fire SBC offers unparalleled opportunities for developers, hobbyists, and researchers to explore and experiment with RISC-V technology. Chipset Features Microchip Polarfire MPFS025T SoC FPGA FPGA Fabric 23K logic elements (4-input LUT + DFF) 68 Math blocks (18x18 MACC) 4 SerDes lanes of 12.7 Gbps Microprocessor Subsystem Processor 1x 64-bit RV64IMAC monitor/boot core (E51) 4x 64-bit RV64GC Application cores (U54-MC) Fmax of 667 MHz (–40°C to 100°C Tj) 3.125 CoreMarks/MHz, 1.714 DMIPS/MHz Storage MMC 5.1 SD/SDIO 1 Quad SPI flash controller 128 KB eNVM 56 KB sNVM Memory Interfaces 36-bit DDR4/DDR3/LPDDR4/LPDDR3 memory controller with SECDED Communication Interfaces 2x GigE MACs, USB 2.0 OTG, 5x multi-mode UARTs, 2x SPI, 2x I²C, 2x CAN 2.0 Controllers. 2x PCIe Gen2 End Points/Root Ports Board Features On-board Memory 2 GB LPDDR4 16 GB Kingston eMMC 128 Mbit SPI flash Connectors and Expansion USB Type-C with high-Speed (480 Mbps) dual-role support and power input Gigabit Ethernet M.2 E-Key socket for WiFi and other PCIe/SDIO modules microSD card socket SYZYGY high-speed connector CSI 22-pin camera connector 2x46-pin BeagleBone Cape add-on headers with on-board ADC Screw terminal for 5 V power input 6-pin 3.3 V UART header JTAG TAG-CONNECT footprint Downloads Documentation

Lees meer minder

The QAV250 Kit is the perfect way to get started developing on either PX4 or Ardupilot. It pairs a carbon fiber 250 racing frame and essential electronics with Pixhawk 6C mini autopilot. The kit is easy to assemble. No soldering needed. Specifications Micro Power Module (PM06 v2) Motors: 2207 KV1950 Wheelbase: 250 mm Dimensions: 198 x 235 x 70 mm Weight: 347 g Included Carbon fiber 250 airframe with hardware Micro Power Module (PM06 v2) Motors: 2207 KV1950 5" Plastic Props Fully assembled Power Management Board with ESCs (BLHeli S ESC 20A) Battery Straps Note: LiPo battery is not included.

Lees meer minder

The X500 V2 ARF Kit is an affordable, lightweight, and robust carbon fiber professional drone kit that is easy to assemble (less than 15 minutes). It comes with the X500 V2 Frame Kit and motors, ESCs, power distribution boards and propellers preinstalled. It is perfectly compatible with various flight controllers such as the Holybro Pixhawk series, Durandal, Pix32 V5, etc. There are numerous improvements compared the previous model. Specifications Wheelbase: 500 mm Motor mount pattern: 16x16 mm Frame body: 144x144 mm, 2 mm thick Landing gear height: 215 mm Space between top and bottom plates: 28 mm Weight: 610 g Flight time: ~18 minutes hover with no additional payload. Tested with 5000 mAh battery. Payload: 1500 g (without battery, 70% throttle) Battery recommendation: 4S 3000-5000 mAh 20C+ with XT60 Lipo battery (not Included) Included X500 V2 Frame Kit With Preinstalled Items: 4x Motors: Holybro 2216 KV920 Motor (4 pcs) with XT30 Plug 4x ESCs (BLHeli S ESC 20A) 6x 1045 Propellers Power Distribution Board – XT60 plug for battery & XT30 plug for ESCs & peripherals Note: Depth camera mount is sold separately.

Lees meer minder

UFactory 850 is the most powerful robot with industrial grade performance. Features 6DoF Payload: 5 kg Reach: 850 mm Repeatability: 0.02 mm Weight: 20 kg Applications Glambot Welding Screwdriving Robot Vision Industrial Production Designed for both mobile platforms and your workbench The AC control box contains an AC-DC adapter inside, 100-240 V AC is all ready to go. The DC control box supports 48-72 V wide inputs, it perfectly fits the battery system on your mobile platform. Flexible Deployment With Safe Feature Hand teaching, space-saving and easy to re-deploy to multiple applications without changing your production layout. Perfectly for recurrent tasks. Collision detection is available for all of our cobots. Your safety is always the top priority. Graphical Interface For Beginner-Friendly Programming Compatible with various operation systems, including macOS and Windows. Web-based technology compatible with all major browsers. Drag and drop to create your code in minutes. Powerful And Open Source SDK At Your Fingertips Fully functional open-source Python/C++ SDK provides more flexible programming. ROS/ROS2 packages are ready-to-go. Example codes help you to deploy the robotic arm smoothly. Specifications UFactory 850 xArm 5 xArm 6 xArm 7 Payload 5 kg 3 kg 5 kg 3.5 kg Reach 850 mm 700 mm 700 mm 700 mm Degrees of freedom 6 5 6 7 Repeatability ±0.02 mm ±0.1 mm ±0.1 mm ±0.1 mm Maximum Speed 1 m/s 1 m/s 1 m/s 1 m/s Weight (robot arm only) 20 kg 11.2 kg 12.2 kg 13.7 kg Maximum Speed 180°/s 180°/s 180°/s 180°/s Joint 1 ±360° ±360° ±360° ±360° Joint 2 -132°?132° -118°?120° -118°?120° -118°?120° Joint 3 -242°~3.5° -225°~11° -225°~11° ±360° Joint 4 ±360° -97°~180° ±360° -11°?225° Joint 5 -124°~124° ±360° -97°~180° ±360° Joint 6 ±360° ±360° -97°~180° Joint 7 ±360° Hardware Ambient Temperature Range 0-50°C Power Consumption Typical 240 W, max 1000 W Input Power Supply 48 V DC, 20.8 A Footprint Ø 190 mm Materials Aluminum, Carbon Fiber Base Connector Type M8x4 ISO Class Cleanroom 5 Robot Mounting Any End Effector Communication Protocol Modbus RTU End Effector I/O 2x DI / 2x DO / 2x AI / 1x RS485 Communication Mode Ethernet Included 1x UFactory 850 robotic arm 1x AC control box 1x Control box power cable

Lees meer minder

This multi-axis robot perfectly balances power and size. Features 6 Axis Payload: 3.5 kg Reach: 700 mm Repeatability: 0.1 mm Max Speed 1000 mm/s Applications Machine Tending Bin Picking Mobile platform Lab Automation Robotic Research Durable Collaborative robots for your automation Industrial-grade harmonic drive and servomotors guarantee 24/7 working without stop. Crafted from Carbon fiber, 15 kg weight makes it possible for easier deployment. Flexible deployment with safe feature Hand teaching, lightweight, space-saving and easy to re-deploy to multiple applications without changing your production layout. Perfectly for recurrent tasks. Collision detection is available for all of our cobots. Your safety is always the top priority. Graphical interface for beginner-friendly programming Compatible with various of operation systems, including macOS and Windows. Web-based technology compatible with all major browsers. Drag and drop to create your code in minutes. Powerful and open source SDK at your fingertips Fully functional open-source Python/C++ SDK provides more flexible programming. ROS/ROS2 packages are ready-to-go. Example codes help you to deploy the robotic arm smoothly. Specifications UFactory 850 xArm 5 xArm 6 xArm 7 Payload 5 kg 3 kg 5 kg 3.5 kg Reach 850 mm 700 mm 700 mm 700 mm Degrees of freedom 6 5 6 7 Repeatability ±0.02 mm ±0.1 mm ±0.1 mm ±0.1 mm Maximum Speed 1 m/s 1 m/s 1 m/s 1 m/s Weight (robot arm only) 20 kg 11.2 kg 12.2 kg 13.7 kg Maximum Speed 180°/s 180°/s 180°/s 180°/s Joint 1 ±360° ±360° ±360° ±360° Joint 2 -132°?132° -118°?120° -118°?120° -118°?120° Joint 3 -242°~3.5° -225°~11° -225°~11° ±360° Joint 4 ±360° -97°~180° ±360° -11°?225° Joint 5 -124°~124° ±360° -97°~180° ±360° Joint 6 ±360° ±360° -97°~180° Joint 7 ±360° Hardware Ambient Temperature Range 0-50°C Power Consumption Min 8.4 W, Typical 200 W, max 400 W Input Power Supply 24 V DC, 16.5 A Footprint Ø 126 mm Materials Aluminum, Carbon Fiber Base Connector Type M5x5 ISO Class Cleanroom 5 Robot Mounting Any End Effector Communication Protocol Modbus RTU(rs485) End Effector I/O 2x DI/2x DO/2x AI/1x RS485 Communication Mode Ethernet Included 1x xArm 5 robotic arm 1x AC control box 1x Robotic arm power cable 1x Robotic arm end effector adapter cable 1x Robotic arm signal cable 1x Control box power cable 1x Network cable 1x Mounting tool 1x Quick start guide

Lees meer minder

This multi-axis robot perfectly balances power and size. Features Payload: 5 kg Reach: 700 mm Repeatability: 0.1 mm Max Speed 1000 mm/s Applications Machine Tending Bin Picking Mobile platform Lab Automation Robotic Research Durable Collaborative robots for your automation Industrial-grade harmonic drive and servomotors guarantee 24/7 working without stop. Crafted from Carbon fiber, 15 kg weight makes it possible for easier deployment. Flexible deployment with safe feature Hand teaching, lightweight, space-saving and easy to re-deploy to multiple applications without changing your production layout. Perfectly for recurrent tasks. Collision detection is available for all of our cobots. Your safety is always the top priority. Graphical interface for beginner-friendly programming Compatible with various of operation systems, including macOS and Windows. Web-based technology compatible with all major browsers. Drag and drop to create your code in minutes. Powerful and open source SDK at your fingertips Fully functional open-source Python/C++ SDK provides more flexible programming. ROS/ROS2 packages are ready-to-go. Example codes help you to deploy the robotic arm smoothly. Specifications UFactory 850 xArm 5 xArm 6 xArm 7 Payload 5 kg 3 kg 5 kg 3.5 kg Reach 850 mm 700 mm 700 mm 700 mm Degrees of freedom 6 5 6 7 Repeatability ±0.02 mm ±0.1 mm ±0.1 mm ±0.1 mm Maximum Speed 1 m/s 1 m/s 1 m/s 1 m/s Weight (robot arm only) 20 kg 11.2 kg 12.2 kg 13.7 kg Maximum Speed 180°/s 180°/s 180°/s 180°/s Joint 1 ±360° ±360° ±360° ±360° Joint 2 -132°?132° -118°?120° -118°?120° -118°?120° Joint 3 -242°~3.5° -225°~11° -225°~11° ±360° Joint 4 ±360° -97°~180° ±360° -11°?225° Joint 5 -124°~124° ±360° -97°~180° ±360° Joint 6 ±360° ±360° -97°~180° Joint 7 ±360° Hardware xArm Robot specs Ambient Temperature Range 0-50°C Power Consumption Min 8.4 W, Typical 200 W, max 400 W Input Power Supply 24 V DC, 16.5 A Footprint Ø 126 mm Materials Aluminum, Carbon Fiber Base Connector Type M5x5 ISO Class Cleanroom 5 Robot Mounting Any End Effector Communication Protocol Modbus RTU(rs485) End Effector I/O 2x DI/2x DO/2x AI/1x RS485 Communication Mode Ethernet Included 1x xArm 5 robotic arm 1x AC control box 1x Robotic arm power cable 1x Robotic arm end effector adapter cable 1x Robotic arm signal cable 1x Control box power cable 1x Network cable 1x Mounting tool 1x Quick start guide

Lees meer minder

This multi-axis robot perfectly balances power and size. Features 5 Axis Payload: 3 kg Reach: 700 mm Repeatability: 0.1 mm Max Speed 1000 mm/s Applications Machine Tending Bin Picking Mobile platform Lab Automation Robotic Research Durable Collaborative robots for your automation Industrial-grade harmonic drive and servomotors guarantee 24/7 working without stop. Crafted from Carbon fiber, 15 kg weight makes it possible for easier deployment. Flexible deployment with safe feature Hand teaching, lightweight, space-saving and easy to re-deploy to multiple applications without changing your production layout. Perfectly for recurrent tasks. Collision detection is available for all of our cobots. Your safety is always the top priority. Graphical interface for beginner-friendly programming Compatible with various of operation systems, including macOS and Windows. Web-based technology compatible with all major browsers. Drag and drop to create your code in minutes. Powerful and open source SDK at your fingertips Fully functional open-source Python/C++ SDK provides more flexible programming. ROS/ROS2 packages are ready-to-go. Example codes help you to deploy the robotic arm smoothly. Specifications UFactory 850 xArm 5 xArm 6 xArm 7 Payload 5 kg 3 kg 5 kg 3.5 kg Reach 850 mm 700 mm 700 mm 700 mm Degrees of freedom 6 5 6 7 Repeatability ±0.02 mm ±0.1 mm ±0.1 mm ±0.1 mm Maximum Speed 1 m/s 1 m/s 1 m/s 1 m/s Weight (robot arm only) 20 kg 11.2 kg 12.2 kg 13.7 kg Maximum Speed 180°/s 180°/s 180°/s 180°/s Joint 1 ±360° ±360° ±360° ±360° Joint 2 -132°?132° -118°?120° -118°?120° -118°?120° Joint 3 -242°~3.5° -225°~11° -225°~11° ±360° Joint 4 ±360° -97°~180° ±360° -11°?225° Joint 5 -124°~124° ±360° -97°~180° ±360° Joint 6 ±360° ±360° -97°~180° Joint 7 ±360° Hardware Ambient Temperature Range 0-50°C Power Consumption Min 8.4 W, Typical 200 W, max 400 W Input Power Supply 24 V DC, 16.5 A Footprint Ø 126 mm Materials Aluminum, Carbon Fiber Base Connector Type M5x5 ISO Class Cleanroom 5 Robot Mounting Any End Effector Communication Protocol Modbus RTU(rs485) End Effector I/O 2x DI/2x DO/2x AI/1x RS485 Communication Mode Ethernet Included 1x xArm 5 robotic arm 1x AC control box 1x Robotic arm power cable 1x Robotic arm end effector adapter cable 1x Robotic arm signal cable 1x Control box power cable 1x Network cable 1x Mounting tool 1x Quick start guide

Lees meer minder

With this comprehensive complete set, you can now enter the fascinating world of electronics. In addition to an Oxocard Connect and a breadboard cartridge, it contains 96 electronic components with which you can build a variety of electronic circuits. Features Free and unlimited access to the nanopy.io editor with a variety of scripts that you can transfer to your Oxocard Connect at the touch of a button. Electronics course with 15 experiments that show you step by step how to switch LEDs, connect a servo, generate acoustic signals with a piezo and much more. Oxocard Connect High quality microcontroller device with TFT screen, glass cover, joystick, USB-C, as well as revolutionary 16-pin cartridge slot. The Oxocard Connect represents the next generation of small experimental computers. The universal cartridge slot allows ready-made or self-developed boards to be brought to life instantly by simply plugging them in. Each card comes with drivers and demo programs installed and automatically loaded and started when plugged in. Breadboard Cartridge With the Breadboard you can quickly plug in your own circuits. A plug-in board with 17 rows is available for this purpose. Connections: two analog inputs, five digital ports, I²C, SPI, GND/V3.3. access to the 5 V power source of the port. Red LEDs are attached to the digital pins. 5 V can also be injected to power the Oxocard Connect without USB. Included 1x Oxocard Connect 1x Breadboard Cartridge Electronic components 1x PIR-Sensor (Motion detector) 1x Thermistor 10 k? (Temperature sensor) 1x Photoresistor 10 k? (Light sensor) 1x Potentiometer 1x Mikroservo SG92R 1x Piezo (Acoustic signals) 3x LED (green, yellow, red) 2x Buttons 9x Resistances 75x Cables (angled) – various colors and lengths

Lees meer minder

De Portenta Vision Shield LoRa voegt industriële functies toe aan uw Portenta. Met deze hardware uitbreiding kunt u embedded computer vision toepassingen uitvoeren, draadloos via LoRa verbinding maken met de Arduino Cloud of met uw eigen infrastructuur, en uw systeem activeren bij het detecteren van geluiden.Deze uitbreidingskaart wordt geleverd met: een 320x320 pixels camerasensor: gebruik een van de cores in de Portenta om beeldherkenningsalgoritmen uit te voeren met behulp van de OpenMV voor Arduino editor draadloze lange afstand 868/915 MHz LoRa connectiviteit: verbind uw energiezuinige Portenta H7 met het Internet of Things twee ingebouwde microfoons voor directionele geluidsdetectie: leg geluid in realtime vast en analyseer dit JTAG-connector: voer low-level foutopsporing uit op uw Portenta board, of speciale firmware-updates met behulp van een externe programmer SD-card connector: sla uw vastgelegde data op de kaart op, of lees configuratiebestanden De Vision Shield LoRa is ontworpen om te werken met de Arduino Portenta H7. De Portenta boards zijn voorzien van multicore 32-bits ARM Cortex processors, die draaien op honderden megahertz, met megabytes aan programmageheugen en RAM. De Portenta boards worden geleverd met WiFi en Bluetooth.Specificaties Fototoestel Himax HM-01B0 camera module (site van de fabrikant) Resolutie 320 x 320 active pixel resolutie, met ondersteuning voor QVGA Beeldsensor High sensitivity 3.6? BrightSense pixeltechnologie Microfoon 2x MP34DT05 (datasheet) Connectiviteit 868/915MHz ABZ-093 LoRa Module met ARM Cortex-M0+ (datasheet) Dimensies 66 x 25 mm Gewicht 8 gr Downloads Datasheet Schematics

Lees meer minder

TurtleBot 4 is the next-generation of the world’s most popular open source robotics platform for education and research, offering better computing power, better sensors and a world class user experience at an affordable price point.TurtleBot 4 Lite is equipped with an iRobot Create 3 mobile base, a powerful Raspberry Pi 4 running ROS 2, OAK-D spatial AI stereo camera, 2D LiDAR and more. All components have been seamlessly integrated to deliver an out-of-the-box development and learning platform.Specifications Base platform iRobot Create 3 Wheels (Diameter) 72 mm Ground Clearance 4.5 mm On-board Computer Raspberry Pi 4 (4 GB) Maximum linear velocity 0.31 m/s in safe mode0.46 m/s without safe mode Maximum angular velocity 1.90 rad/s Maximum payload 9 kg Operation time 2h 30m – 4h depending on load Charging time 2h 30m Lidar RPLIDAR A1M8 Camera OAK-D-Lite User Power VBAT @1.9 A5 V @ Low current3.3 V @ Low current USB Expansion 2x USB 2.0 (Type A)2x USB 3.0 (Type A) Programmable LEDs Create 3 Lightring Buttons and Switches 2x Create 3 User buttons1x Create 3 Power Button Battery 26 Wh Lithium Ion (14.4 V nominal) Charging Dock Included Size (L x W x H) 342 x 339 x 192 mm Weight 3.3 kg DownloadsUser Manual

Lees meer minder

World’s Most Popular ROS PlatformTurtleBot is the most popular open source robot for education and research. The new generation TurtleBot3 is a small, low cost, fully programmable, ROS based mobile robot. It is intended to be used for education, research, hobby and product prototyping.Affordable CostTurtleBot was developed to meet the cost-conscious needs of schools, laboratories and companies. TurtleBot3 is the most affordable robot among the SLAM-able mobile robots equipped with a 360° Laser Distance Sensor LDS-01.ROS StandardThe TurtleBot brand is managed by Open Robotics, which develops and maintains ROS. Nowadays, ROS has become the go-to platform for all the roboticists around the world. TurtleBot can be integrated with existing ROS-based robot components, but TurtleBot3 can be an affordable platform for whom want to get started learning ROS.ExtensibilityTurtleBot3 encourages users to customize its mechanical structure with some alternative options: open source embedded board (as a control board), computer and sensors. TurtleBot3 Waffle Pi is a two-wheeled differential drive type platform but it is able to be structurally and mechanically customized in many ways: Cars, Bikes, Trailers and so on. Extend your ideas beyond imagination with various SBC, sensors and motors on a scalable structure.Modular Actuator for Mobile RobotTurtleBot3 is able to get a precise spatial data by using 2 DYNAMIXEL’s in the wheel joints. DYNAMIXEL XM series can be operated by one of 6 operating modes (XL series: 4 operating modes): Velocity control mode for wheels, Torque control mode or Position control mode for joint, etc. DYNAMIXEL can be used even to make a mobile manipulator which is light but can be precisely controlled with velocity, torque and position control. DYNAMIXEL is a core component that makes TurtleBot3 perfect. It is easy to assemble, maintain, replace and reconfigure.Open Control Board for ROSThe control board is open-sourced in hardware wise and in software wise for ROS communication. The open source control board OpenCR1.0 is powerful enough to control not only DYNAMIXEL’s but also ROBOTIS sensors that are frequently being used for basic recognition tasks in cost effective way. Various sensors such as Touch sensor, Infrared sensor, Color sensor and a handful more are available. The OpenCR1.0 has an IMU sensor inside the board so that it can enhance precise control for countless applications. The board has 3.3 V, 5 V, 12 V power supplies to reinforce the available computer device lineups.Open SourceThe hardware, firmware and software of TurtleBot3 are open source which means that users are welcomed to download, modify and share source codes. All components of TurtleBot3 are manufactured with injection molded plastic to achieve low cost, however, the 3D CAD data is also available for 3D printing.Specifications Maximum translational velocity 0.26 m/s Maximum rotational velocity 1.82 rad/s (104.27 deg/s) Maximum payload 30 kg Size (L x W x H) 281 x 306 x 141 mm Weight (+ SBC + Battery + Sensors) 1.8 kg Threshold of climbing 10 mm or lower Expected operating time 2h Expected charging time 2h 30m SBC (Single Board Computers) Raspberry Pi 4 (2 GB RAM) MCU 32-bit ARM Cortex-M7 with FPU (216 MHz, 462 DMIPS) Remote Controller RC-100B + BT-410 Set (Bluetooth 4, BLE) Actuator XL430-W210 LDS (Laser Distance Sensor) 360 Laser Distance Sensor LDS-01 or LDS-02 Camera Raspberry Pi Camera Module v2.1 IMU Gyroscope 3 AxisAccelerometer 3 Axis Power connectors 3.3 V/800 mA5 V/4 A12 V/1 A Expansion pins GPIO 18 pinsArduino 32 pin Peripheral 3x UART, 1x CAN, 1x SPI, 1x I²C, 5x ADC, 4x 5-pin OLLO DYNAMIXEL ports 3x RS485, 3x TTL Audio Several programmable beep sequences Programmable LEDs 4x User LED Status LEDs 1x Board status LED1x Arduino LED1x Power LED Buttons and Switches 2x Push buttons, 1x Reset button, 2x Dip switch Battery Lithium polymer 11.1 V 1800 mAh / 19.98 Wh 5C PC connection USB Firmware upgrade via USB / via JTAG Power adapter (SMPS) Input: 100-240 VAC 50/60 Hz, 1.5 A @maxOutput: 12 VDC, 5 A Downloads ROS Robot Programming GitHub E-Manual Community

Lees meer minder

The X-Carve CNC machine is great for Makers looking to start their CNC journey. Reliable, customizable, and expandable: X-Carve is also the best-selling machine for entrepreneurs and small businesses. Start producing, no CNC knowledge required. X-Carve and Easel simplify 3D carving so you can begin working with wood, plastics and other materials in minutes. Features Carves wood, plastics, and materials like aluminum, Corian®?, and linoleum up to 37 inches wide. Easy-to-follow assembly instructions will help familiarize you with your machine. This model V2 is 3x faster, more rigid, and more accurate than the original X-Carve. Design -> Carve -> Sell Design: Sketch out your own idea and upload to Easel software, or browse from the library of over 3 million designs. Carve: Easel controls the spindle and makes calculations so there's no guesswork. Sell: X-Carve + Easel speeds up production so you can take on more jobs and get them out faster. The bundle pays for itself in no time. Carvable Materials Wood/Wood Composites: Hardwoods, softwoods, MDF, plywoods, etc. Plastics: HDPE, Delrin®?, polycarbonate, acrylic, Corian®?, etc. Non-Ferrous Metals: Aluminum, brass, copper, etc. Import File Types: G-Code, SVG, or DXF files from any software Software Compatible with standard g-code and GRBL 1 Year of Easel Pro Included (world’s easiest CAD/CAM software) Size & Weight Work Area: 750 x 750 x 114 mm (29.5 x 29.5 x 4.5') Machine Footprint: 1041 x 1321 x 559 mm (41 x 52 x 22') Maximum Passthrough Sheet Width: 940 mm (37') Finish: Anodized Aluminum Product Weight: 45 kg Shipping Weight: 50 kg Included X-Carve Base & Hardware Rail Kit DeWalt 26200 Spindle X-Controller Kit Nema 23 Motors Kit Waste Board Drag Chain Toolkit Homing Kit Z-Probe Kit Side Board Dust Control System Clamp Set Digital Calipers 1 Year Easel Pro Software Downloads Instructions Support 3D Models and Drawings

Lees meer minder

De Unitree Go1 serie bestaat uit viervoetige robots voor research & development van autonome systemen op het gebied van mens-robot interactie (HRI), SLAM & transport. Door het hebben van vier poten en een 12-DOF houdingscontrole kan deze robot veel verschillende terreinen aan. De Go1 wordt geleverd met een geperfectioneerde aandrijving en power management systeem, wat een snelheid (afhankelijk van de uitvoering) tot 3,7 m/s of 11,88 km/u mogelijk maakt bij een bedrijfstijd van maximaal 2,5 uur. Verder hebben de motoren een koppel van 23,70 Nm op de body/dijen en 35,55 Nm op de knieën, waardoor ook sprongen of backflips mogelijk zijn. Kenmerken High Dynamics 17 km/u Intelligent Side-Follow System (ISS) Super Sensorisch System (SSS) 10-view Detectie AI-detectie, Human Recognition, enz. Flexibele en adaptieve gewrichten Langdurige werking Specificaties Licht en compact Gewicht: 12 kg Afmetingen (ingeklapt): 0,588 x 0,29 x 0,22 m High performance Max snelheid: 4,7 m/s (17 km/u of 10,6 mph) Intelligent Side Follow System (gepatenteerde Wireless Vector Positioning and Control Technology) De robothond kan naast zijn baasje lopen en niet alleen volgen De interactie tussen mens en machine is zowel harmonieus als veilig Super Sensory System Full View Coverage 5 sets fish-eye stereo dieptecamera's + AI-nabewerking + 3 sets hypersonische sensoren Lens openingshoek: 150 x 170° Ingebouwde krachtige AI 16-core CPU + GPU (384 cores, 1,5 TFLOPS) ISS en SSS werken coöperatief samen Robuust en betrouwbaar Power System Nieuwe superlichtgewicht Power Joint met laag geluidsniveau en een lange levensduur Heat Pipe koelsysteem ingebouwd in de motor van het knie gewricht Body/dijen gewrichten: C1-8: 520 g 23,70 N.m Knie gewricht: C1-8 x 1,5 ratio 35,55 N.m Unitree Go1 varianten De Go1 serie heeft 3 varianten (Go1 Air, Go1 Pro en Go1 Edu), die technisch enigszins verschillen. De verschillen betreffen vooral de processoren en de sensor systemen. De Air en Pro variant werken, afhankelijk van het model, met één of 3x (4x 1,43 GHz 128 Cores 0,5 T) processor en met 1 of 5 super sensor systems. Beide varianten zijn uitgerust met 3 ultrasone sensoren. De Go1 Edu-variant heeft tot 3 nano processors, 5 super sensor systems en 4 ultrasone sensoren. De Edu Plus daarentegen is standaard uitgerust met een Nvidia Jetson Xavier NX. Model vergelijking Go1 Air Go1 Pro Go1 Edu Go1 Edu Plus SSS 1 Super Sensing System 1 set 5 sets 5 sets 5 sets Sensing calculatie 1x (4x 1,43 GHz 128 cores 0.5 T) 3x (4x 1,43 GHz 128 cores 0.5 T) 3 Jetson Nano 2 Jetson Nano + 1 NVIDIA Jetson NX ISS 1 Intelligent Concomitant ? ? ? ? RTT 1 Pictures Transaction ? ? ? ? Oplader 24 V, 4 V 24 V, 6 V 24 V, 6 V 24 V, 6 V Afstandsbediening ? ? ? ? Draagvermogen ?3 kg ?3 kg ?5 kg (max ~10 kg) ?5 kg (max ~10 kg) Heat Pipe ondersteunde warmteafvoer ? ? ? ? Bewegingssnelheid 0 ~ 2,5 m/s 0 ~ 3,5 m/s 0 ~ 3,7 m/s (max ~5 m/s) 0 ~ 3,7 m/s (max ~5 m/s) Accu 1x 1x 1x 1x Grafische programming interface ? ? ? ? Scientific programming interface ? ? Python programming interface ? ? HAI 1 Human Sensing ? ? APP Top View ? ? ? 4G ? ? Voeteinde fysieke kracht sensor ? ? Multifunctionele uitbreidingsinterface voor randapparatuur ? ? Radar 2D of 3D optioneel 2D of 3D optioneel Inbegrepen 1x Unitree Go1 1x Unitree Go1 Accu 1x Unitree Go1 Oplader 1x Unitree Go1 Afstandsbediening Downloads Handleiding GitHub

Lees meer minder

Unitree Go1 series consists of quadruped robots for the research & development of autonomous systems in the fields of human-robot interaction (HRI), SLAM & transportation. Due to the four legs, as well as the 12DOF, this robot can handle a variety of different terrains. The Go1 comes with a perfected drive & power management system, which enables a speed (depending on the version) of up to 3.7 m/s or 11.88 km/h with an operating time of up to 2.5 hours. Furthermore, the motors have a torque of 23.70N.m at the body/thighs and 35.55N.m at the knees, which also allow jumps or backflips. Features High Dynamics 17 km/h Intelligent Side-Follow System (ISS) Super Sensory System (SSS) 10-view Detection AI Detection, Human Recognition, etc. Flexible and adaptive Joints Long Endurance Specifications Light and Compact Weight: 12 kg Size (folded): 0.588 x 0.29 x 0.22 m High Performance Max Speed: 4.7 m/s (17 kmh or 10.6 mph) Intelligent Side Follow System (Adopt Patented Wireless Vector Positioning and Control Technology) Robot dog can walk alongside its owner and not only follow The human-machine interaction is both harmonious and safe Super Sensory System Full View Coverage 5 Sets Fish-Eye Stereo Depth Cameras + AI Post-processing + 3 Sets of Hypersonic Sensors Lens Angle: 150 x 170° Built-in Powerful AI 16-core CPU + GPU (384 Cores, 1.5 TFLOPS) ISS and SSS Function Cooperatively Strong & Reliable Power System New Power Joint with Super Lightweight Low Noise and Long Life Heat Pipe Cooling System Built in the Knee Joint Motor Body/thigh joints: C1-8: 520 g 23.70N.m Knee Joint: C1-8 x 1.5 ratio 35.55N.m Unitree Go1 Variants The Go1 series has 3 variants (Go1 Air, Go1 Pro and Go1 Edu), which differ a little technically. The differences are mainly the processors and sensor systems, the Air and Pro variant works, depending on the model, with one or 3x (4x 1.43 GHz 128 Cores 0.5 T) processor as well as with 1 or 5 super sensor systems. Both variants are equipped with 3 ultrasonic sensors. The Go1 Edu variant has up to 3 nano processors, 5 super sensor systems, and 4 ultrasonic sensors. In contrast, Edu Plus is equipped with an Nvidia Jetson Xavier NX as standard. Model Comparison   Go1 Air Go1 Pro Go1 Edu Go1 Edu Plus SSS 1 Super-sensing system 1 set 5 sets 5 sets 5 sets Sensing calculation 1x (4x 1.43 GHz 128 Cores 0.5 T) 3x (4x 1.43 GHz 128 Cores 0.5 T) 3 Jetson Nano 2 Jetson Nano + 1 NVIDIA Jetson NX ISS 1 Intelligent Concomitant ? ? ? ? RTT 1 Pictures Transaction ? ? ? ? Charger 24 V, 4 V 24 V, 6 V 24 V, 6 V 24 V, 6 V Remote Control ? ? ? ? Load ?3 kg ?3 kg ?5 kg (max ~10 kg) ?5 kg (max ~10 kg) Heat Pipe Assisted Heat Dissipation ? ? ? ? Motion Speed 0~2.5 m/s 0~3.5 m/s 0~3.7 m/s (max ~5 m/s) 0~3.7 m/s (max ~5 m/s) Battery 1x 1x 1x 1x Graphical Programming Interface ? ? ? ? Scientific Programming Interface     ? ? Python Programming Interface     ? ? HAI 1 Human Sensing     ? ? APP Top View   ? ? ? 4G     ? ? Foot-end Physical Force Sensor     ? ? Multifunctional Peripheral Expansion Interface     ? ? Radar     2D or 3D optional 2D or 3D optional Included 1x Unitree Go1 1x Unitree Go1 Battery 1x Unitree Go1 Charger 1x Unitree Go1 Remote Controller Downloads User Manual GitHub

Lees meer minder

Unitree Go1 series consists of quadruped robots for the research & development of autonomous systems in the fields of human-robot interaction (HRI), SLAM & transportation. Due to the four legs, as well as the 12DOF, this robot can handle a variety of different terrains. The Go1 comes with a perfected drive & power management system, which enables a speed (depending on the version) of up to 3.7 m/s or 11.88 km/h with an operating time of up to 2.5 hours. Furthermore, the motors have a torque of 23.70N.m at the body/thighs and 35.55N.m at the knees, which also allow jumps or backflips. Features High Dynamics 17 km/h Intelligent Side-Follow System (ISS) Super Sensory System (SSS) 10-view Detection AI Detection, Human Recognition, etc. Flexible and adaptive Joints Long Endurance Specifications Light and Compact Weight: 12 kg Size (folded): 0.588 x 0.29 x 0.22 m High Performance Max Speed: 4.7 m/s (17 kmh or 10.6 mph) Intelligent Side Follow System (Adopt Patented Wireless Vector Positioning and Control Technology) Robot dog can walk alongside its owner and not only follow The human-machine interaction is both harmonious and safe Super Sensory System Full View Coverage 5 Sets Fish-Eye Stereo Depth Cameras + AI Post-processing + 3 Sets of Hypersonic Sensors Lens Angle: 150 x 170° Built-in Powerful AI 16-core CPU + GPU (384 Cores, 1.5 TFLOPS) ISS and SSS Function Cooperatively Strong & Reliable Power System New Power Joint with Super Lightweight Low Noise and Long Life Heat Pipe Cooling System Built in the Knee Joint Motor Body/thigh joints: C1-8: 520 g 23.70N.m Knee Joint: C1-8 x 1.5 ratio 35.55N.m Unitree Go1 Variants The Go1 series has 3 variants (Go1 Air, Go1 Pro and Go1 Edu), which differ a little technically. The differences are mainly the processors and sensor systems, the Air and Pro variant works, depending on the model, with one or 3x (4x 1.43 GHz 128 Cores 0.5 T) processor as well as with 1 or 5 super sensor systems. Both variants are equipped with 3 ultrasonic sensors. The Go1 Edu variant has up to 3 nano processors, 5 super sensor systems, and 4 ultrasonic sensors. In contrast, Edu Plus is equipped with an Nvidia Jetson Xavier NX as standard. Model Comparison   Go1 Air Go1 Pro Go1 Edu Go1 Edu Plus SSS 1 Super-sensing system 1 set 5 sets 5 sets 5 sets Sensing calculation 1x (4x 1.43 GHz 128 Cores 0.5 T) 3x (4x 1.43 GHz 128 Cores 0.5 T) 3 Jetson Nano 2 Jetson Nano + 1 NVIDIA Jetson NX ISS 1 Intelligent Concomitant ? ? ? ? RTT 1 Pictures Transaction ? ? ? ? Charger 24 V, 4 V 24 V, 6 V 24 V, 6 V 24 V, 6 V Remote Control ? ? ? ? Load ?3 kg ?3 kg ?5 kg (max ~10 kg) ?5 kg (max ~10 kg) Heat Pipe Assisted Heat Dissipation ? ? ? ? Motion Speed 0~2.5 m/s 0~3.5 m/s 0~3.7 m/s (max ~5 m/s) 0~3.7 m/s (max ~5 m/s) Battery 1x 1x 1x 1x Graphical Programming Interface ? ? ? ? Scientific Programming Interface     ? ? Python Programming Interface     ? ? HAI 1 Human Sensing     ? ? APP Top View   ? ? ? 4G     ? ? Foot-end Physical Force Sensor     ? ? Multifunctional Peripheral Expansion Interface     ? ? Radar     2D or 3D optional 2D or 3D optional Included 1x Unitree Go1 1x Unitree Go1 Battery 1x Unitree Go1 Charger 1x Unitree Go1 Remote Controller Downloads User Manual GitHub

Lees meer minder