IoT & LoRa

3 producten


  • iLabs LoRa Antenna (EU868)

    iLabs iLabs LoRa Antenna (EU868)

    This is a 170 mm long 868 MHz 50 hm antenna kit targeted for use with iLabs Challenger LoRa products.The antenna can tilt and swivel making it easy to install it in various applications.The kit also comes with a RF cable assembly containing an SMA (Female) and JK-IPEX/MHF/U.FL for connection to the PCB. The coax is a 1-13 mm 50 Ohm cable and is 100 mm’s long.

    € 7,95

    Leden € 7,16

  • iLabs Challenger RP2040 LoRa (EU868)

    iLabs iLabs Challenger RP2040 LoRa (EU868)

    The Challenger RP2040 LoRa is an Arduino/CircuitPython compatible Adafruit Feather format microcontroller board based on the Raspberry Pi Pico (RP2040) chip.The transceiver features a LoRa long range modem that provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption.LoRaThe integrated module LoRa module (RFM95W) can achieve a sensitivity of over -148 dBm utilizing a low cost crystal and bill of materials. The high sensitivity combined with the integrated +20 dBm power amplifier yields industry leading link budget making it optimal for any application requiring range or robustness. LoRa also provides significant advantages in both blocking and selectivity over conventional modulation techniques, solving the traditional design compromise between range, interference immunity and energy consumption.The RFM95W is connected to the RP2040 via SPI channel 1 and a few GPIO’s that is required for signaling. A U.FL connector is used to attach your LoRa antenna to the board. 168 dB maximum link budget +20 dBm – 100 mW constant RF output vs. V supply +14 dBm high efficiency PA Programmable bit rate up to 300 kbps High sensitivity: down to -148 dBm Bullet-proof front end: IIP3 = -12.5 dBm Excellent blocking immunity Low RX current of 10.3 mA, 200 nA register retention Fully integrated synthesizer with a resolution of 61 Hz FSK, GFSK, MSK, GMSK, LoRaTM and OOK modulation Built-in bit synchronizer for clock recovery Preamble detection 127 dB Dynamic Range RSSI Automatic RF Sense and CAD with ultra-fast AFC Packet engine up to 256 bytes with CRC Specifications Microcontroller RP2040 from Raspberry Pi (133 MHz dual-core Cortex-M0) SPI Two SPI channels configured (second SPI connected to RFM95W) I²C One I²C channel configured UART One UART channel configured Analog inputs 4 analog input channels Radio module RFM95W from Hope RF Flash memory 8 MB, 133 MHz SRAM memory 264 KB (divided into 6 banks) USB 2.0 controller Up to 12 MBit/s full speed (integrated USB 1.1 PHY) JST Battery connector 2.0 mm pitch On board LiPo charger 450 mA standard charge current Dimensions 51 x 23 x 3,2 mm Weight 9 g Downloads Datasheet Design files

    € 24,95

    Leden € 22,46

  •  -22% iLabs Challenger RP2040 NFC

    iLabs iLabs Challenger RP2040 NFC

    The Challenger RP2040 NFC is a small embedded computer, equipped with an advanced on-board NFC controller (NXP PN7150), in the popular Adafruit Feather form factor. It is based on an RP2040 microcontroller chip from the Raspberry Pi Foundation which is a dual-core Cortex-M0 that can run on a clock up to 133 MHz. NFC The PN7150 is a full featured NFC controller solution with integrated firmware and NCI interface designed for contactless communication at 13.56 MHz. It is fully compatible with NFC forum requirements and is greatly designed based on learnings from previous NXP NFC device generation. It is the ideal solution for rapidly integrating NFC technology in any application, especially small embedded systems reducing Bill of Material (BOM). The integrated design with full NFC forum compliancy gives the user all the following features: Embedded NFC firmware providing all NFC protocols as pre-integrated feature. Direct connection to the main host or microcontroller, by I²C-bus physical and NCI protocol. Ultra-low power consumption in polling loop mode. Highly efficient integrated power management unit (PMU) allowing direct supply from a battery. Specifications Microcontroller RP2040 from Raspberry Pi (133 MHz dual-core Cortex-M0) SPI One SPI channels configured I²C Two I²C channel configured (dedicated I²C for the PN7150) UART One UART channel configured Analog inputs 4 analog input channels NFC module PN7150 from NXP Flash memory 8 MB, 133 MHz SRAM memory 264 KB (divided into 6 banks) USB 2.0 controller Up to 12 MBit/s full speed (integrated USB 1.1 PHY) JST Battery connector 2.0 mm pitch On board LiPo charger 450 mA standard charge current Dimensions 51 x 23 x 3,2 mm Weight 9 g Note: Antenna is not included. Downloads Datasheet Quick start example

    € 22,95€ 17,95

    Leden identiek

Wat is het Internet of Things (IoT)?

Het Internet of Things, of IoT, is een systeem van onderling verbonden computer-apparaten, fysieke objecten met sensoren, verwerkingsvermogen, software, en andere technologieën die unieke identificatiecodes (UID) hebben. Het IoT netwerk heeft te maken met de communicatie tussen machines, de identificatie van apparaten, en de communicatie. Daarom is het kiezen van het beste draadloze netwerk op basis van de IoT specificaties essentieel.

IoT apparaten kunnen gegevens over een netwerk overbrengen zonder dat interactie van mens tot mens of van mens tot computer nodig is. Daardoor kunnen gebruikers moeilijkheden ondervinden met beveiliging, integratie, procescapaciteit, schaalbaarheid, en toegankelijkheid. Om deze problemen op te lossen is een slimme aanpak van het beheer van IoT apparaten nodig.

Wat zijn LoRa en LoRaWAN?

LoRa maakt transmissies over zeer grote afstanden mogelijk (meer dan 10 km in landelijke gebieden) met een laag stroomverbruik. Het is wereldwijd een veel gebruikte technologie voor IoT netwerken. Dankzij de LoRa technologie kunnen we enkele van 's werelds grootste problemen oplossen: energiebeheer, vermindering van natuurlijke hulpbronnen, milieubescherming, efficiëntie van infrastructuur, rampenbestrijding, en meer.

De lage bandbreedte van LoRa kan echter niet voor zomaar elke toepassing gebruikt worden. Als gevolg van beperkingen in het frequentiebereik dat het gebruikt, is het protocol niet in staat continu te zenden.

LoRaWAN is een low-power, wide area networking protocol dat gebouwd is op de LoRa radiomodulatietechniek. Het verbindt apparaten draadloos met het Internet en beheert de communicatie tussen end-node apparaten en netwerk gateways. Zo definieert LoRaWAN het communicatieprotocol en de systeemarchitectuur voor het netwerk, terwijl de fysieke laag van LoRa de communicatieverbinding over lange afstand mogelijk maakt, met de hulp van de gateway.

De gateway helpt om transmissie van een elektrisch apparaat naar de cloud te realiseren, vooral in omgevingen waar andere soorten netwerken door technische beperkingen niet bruikbaar zijn.

Wat kun je met LoRa technologie doen? Wat biedt Elektor aan? Welke accessoires zijn er?

LoRa is een uitstekende keuze voor gebruik binnenshuis in een breed spectrum van toepassingen, waaronder smart cities, gebouwen, landbouw, meting, gezondheidszorg, en logistiek. Het is veilig, bidirectioneel, low-power, en heeft een groot bereik.

Accessoires helpen gebruikers hun IoT opstellingen te optimaliseren. Elektor biedt een ruime keuze aan componenten, waaronder gateways, RFID-lezers, IoT-shields, en verschillende soorten sensoren (bv. temperatuur, positie, en luchtvochtigheid) om aan de diverse behoeften van een groot aantal klanten te voldoen.

De toekomst van LoRa

LoRa zal de kosten helpen verlagen om IoT oplossingen te maken en grootschalige IoT toepassingen mogelijk te maken. Verwacht wordt dat het een sleutelrol zal spelen als communicatienetwerk. We verwachten bijvoorbeeld dat het gebruikt zal worden voor een breed scala van toepassingen, zoals talloze slimme verlichtingssystemen, het volgen van het gebruik van waterkracht, en industriële gegevensbewaking en -analyse.

Login

Wachtwoord vergeten?

Heb je nog geen account?
Maak account aan